Clik here to view.
ElecFreaks Micro:bit Breakout Board
Description: We all know the side pin on BBC Micro:bit board can lead to the input signal or generate control signal with special interface. As for pins of 0/1/2/3V/GND, we can use alligator clip to...
View ArticleClik here to view.
Dust Sensor - Sharp GP2Y1010AU0F
GP2Y1010AU0F is a dust sensor by optical sensing system. An infrared emitting diode (IRED) and an phototran-sistor are diagonally arranged into this device. It detects the reflected light of dust in...
View ArticleClik here to view.
DSO138 2.4" TFT Digital Oscilloscope Kit DIY parts (1Msps)
Feature - Use as a training for electronic production, including schematic, guidance, troubleshooting method - Diversify Components to student for more knowledge - Make a practical tool for audio,...
View ArticleClik here to view.
Double-Sided Protoboard 8cm x 12cm
FATURES: Pads on Double-sided No odor Finely drilled Tough Including power pad Clean hole Points:30x41 Comepare with the single side one: Price: $0.99 Special Price: $0.84
View ArticleClik here to view.
Double-Sided Protoboard 6cm x 8cm
FATURES: Pads on Double-sided No odor Finely drilled Tough Including power pad Clean hole Points:22x27 Comepare with the single side one: Price: $0.53 Special Price: $0.45
View ArticleClik here to view.
Double-Sided Protoboard 5cm x 7cm
FATURES: Pads on Double-sided No odor Finely drilled Tough Including power pad Clean hole Points:18x24 Comepare with the single side one: Price: $0.50 Special Price: $0.43
View ArticleClik here to view.
Double-Sided Protoboard 3cm x 7cm
FATURES: Pads on Double-sided No odor Finely drilled Tough Including power pad Clean hole Points:10x24 Comepare with the single side one: Price: $0.42 Special Price: $0.36
View ArticleClik here to view.
Double-Sided Protoboard 2cm x 8xm
FATURES: Pads on Double-sided No odor Finely drilled Tough Including power pad Clean hole Points:6x28 Comepare with the single side one: Price: $0.32 Special Price: $0.27
View ArticleClik here to view.
DIY Amplifier Speaker Kit Acrylic case
Schematic PCB Assembly The corresponding position of the components are shown in the figure above. The finish effect is as follows: 3.5 mm Audio port soldering PCB wiring diagram Assembly...
View ArticleClik here to view.
Digital relative humidity temperature sensor DHT22
DHT22 output calibrated digital signal. It utilizes exclusive digital-signal-collecting-technique and humidity sensing technology, assuring its reliability and stability.Its sensing elements is...
View ArticleClik here to view.
Digital relative humidity temperature sensor DHT11
DHT11 output calibrated digital signal. It utilizes exclusive digital-signal-collecting-technique and humidity sensing technology, assuring its reliability and stability. Its sensing elements is...
View ArticleClik here to view.
DDS Signal Generator-SG100x/FY10052
OverviewSG100x is a signal generator with FPGA technology, which is based on Direct Digital Synthesis(DDS). It can output the TTL with high stability and measure the frequency accurately. The output...
View ArticleClik here to view.
DDS Function Signal Pulse Generator Sine Square Sawtooth Triangle ECG Wave
Specification:• Operating voltage: DC 5v, DC 12v.• High-speed frequency (HS) output up to 8MHz.• DDS signal amplitude of the offset amount can be adjusted separately by two potentiometers.• DDS...
View ArticleClik here to view.
DCDC Rectifier Power Module
Specifications: Voltage: 4.5-24V Output voltage range: 0.93V-20V(Buck mode, the input must be greater than the output 2V) Output current:: 2A continuous output Output power: Maximum 20W Voltage...
View ArticleClik here to view.
DCDC LC LM2577 Step-Up Module INPUT 3.5-35V OUTPUT 5-56V
Specifications: Input voltage range：3.5V-35V(Must be guaranteed to set the output voltage is higher than the input voltage) Output voltage range: 5.0V-56V Input maximum current: 3A(Depending on power...
View ArticleClik here to view.
DCDC 6.5-22V to 3.3V/5V for Satellite Finder Power Supply
DCDC Satellite Finder power supply board Specifications: Dimensions: L * W * H--- 5.5cm*3.8cm*1.5cm(With fixed column) This version of the 3-way output to meet the need 3.3V high-current power supply...
View ArticleClik here to view.
DCDC 2596S-ADJ Step-down Module
Dimensions: L * W * H-- 4.3cm * 3.0cm * 1.2cm Input voltage: 4.5-30V voltage output: 1.25V-26V Greater continuous current output 2A, peak 3A output Price: $7.80 Special Price: $6.63
View ArticleClik here to view.
DC 5v Fan + Aluminum Heatsink for Raspberry Pi MOS Cooling Set
Package include: 1 Set( 1*5v DC fan + 4 pieces screw ) Fan Size:30x30x11mm / 1.18 x 1.18 x 0.39 inch Connector: 2 pin Rated Voltage: DC 5V Current: 0.2A 2 pieces 8*8*4 mm Aluminum Heatsink 1 pieces...
View ArticleClik here to view.
Customized Order For Topping
For better process management and your conveneince, you may purchase corresponding qty of this payment unit to amount, Please inform us about quotation number in the comment. Thank You very much...
View ArticleClik here to view.
Color Sensor Module COLSEN01
The Color sensor module based on TCS3200, which is a programmable color light-to-frequency converter, it could filter RGB data from source light and convert it to a square wave(50% duty cycle) with...
View Article